The F96 error code indicates that you have a problem with your cooling/blower fan and that part may need to be replaced. I hope that helps. Good luck with your repair.
Contents
- 1 How do I reset the error code on my GE oven?
- 2 How do you reset a GE oven?
- 3 How do I fix F97?
- 4 How do I fix F9 code on GE oven?
- 5 How do I troubleshoot my GE oven?
- 6 How do I reset my oven control board?
- 7 Why is my oven on but not heating up?
- 8 How do I know if my oven control board is bad?
- 9 Why is my GE oven not heating up?
- 10 What is F9 code on GE oven?
- 11 How do I clear E1 F9 code?
- 12 How do I clear F9 code?
- 13 How do I fix F2 error on GE oven?
How do I reset the error code on my GE oven?
If you still see an error code on the GE profile oven, control panel reset is the next step. You can perform a reset by shutting off the breaker that supplies power to your oven. Turn off the breaker in your home’s electrical service panel and leave it off for a full 30 seconds. Then, turn the breaker back on.
How do you reset a GE oven?
Reset the electronic control. Turn the circuit breaker to the OFF position or remove the fuse. Wait one minute, then turn the circuit breaker back to the ON position or install the fuse to reset power to the unit. This should reset the electronic controls on the range or wall oven.
How do I fix F97?
An F97 error code usually means that an internal component needs to be replaced. Have you tried to disconnect power from the appliance for 30 seconds – 1 minute and then reconnect power? This can sometimes reset the internal electronics and clear the code.
How do I fix F9 code on GE oven?
The F9 error usually means the door switch circuit system is faulty. This can be addressed by checking the door switch itself. If the door switch is dirty or caught in one position, use a damp cloth to wipe the switch clean and then wiggle the switch slightly to make sure the switch moves back and forth.
How do I troubleshoot my GE oven?
How to Troubleshoot a GE Electric Oven
- Make sure your GE electric oven controls are set for either bake or broil if the oven does not heat, but the burners do heat.
- Check the oven knobs and make sure they are in the right position if the device is not producing heat.
- Unplug your GE electric oven and check the fuse.
How do I reset my oven control board?
But the first thing you should do is try to perform a hard reset by unplugging the oven, waiting about 30 seconds, and then plugging it back in again. In some cases, this will be enough to reset the control board and get your oven working again.
Why is my oven on but not heating up?
This can be caused by a faulty temperature sensor or a temperature sensor that is touching the wall of the oven. Cause: If it’s still not heating to the correct temperature and you’ve checked or replaced the heating elements, gas igniter and temperature sensor, it may simply need to be calibrated.
How do I know if my oven control board is bad?
I would inspect and look for any burn spots on the control board, burned or broken wires, and if you have access to an multimeter or ohm meter you can test the bake and broil elements for continuity. This is how you can test the elements to see if they are good or bad.
Why is my GE oven not heating up?
If you have a gas oven that won’t heat up, there’s a good chance the bake ignitor needs to be cleaned, repaired, or replaced. When you turn on the oven, you should hear the ignitor click a few times before the gas ignites inside the oven. If it doesn’t, turn off the oven to prevent the spread of gas.
What is F9 code on GE oven?
An F9 error code on a General Electric (GE) oven indicates that the oven’s electronic control system has detected a problem with the automatic door lock. The malfunction may be a jammed door lock mechanism, a pinched or broken wire, a faulty lock switch or a fault in the control board itself.
How do I clear E1 F9 code?
Filter clogged It picks up trash and small objects before they reach the pump, instigating error code E1 F9. To access the filter, unscrew and remove the front panel. Then gently turn it and remove it from the groove.
How do I clear F9 code?
How to Remove the F9 Code From Maytag
- Hold on the “Start/Stop” button for 10 seconds. This will end the beeping.
- Open the oven door and check the door latch.
- Spray a little WD-40 onto a washcloth and scrub off any rust or debris on the latch.
- Press the oven door shut gently.
- Test the oven.
How do I fix F2 error on GE oven?
If the F2 error code has frozen on the oven after shutting down, then unplug the oven for 30 seconds. Plug the oven back in and see if the error code appears again. At times glitches will occur and the error code will randomly appear.
