Readers ask: How Deep Can A Miter Saw Cut?

Saws start to differ when you look at their blade diameter—commonly 10 inches or 12 inches. The bigger the blade, the deeper and wider its maximum cut. Typically, a 10-inch miter saw will cut a 2 x 6 at 90 degrees and a 2 x 4 at 45 degrees; a 12-inch miter saw will cut a 2 x 8 at 90 degrees and a 2 x 6 at 45 degrees.

How deep can a Mitre saw cut?

The maximum depth of cut available with a sliding mitre saw is usually no greater with the simple chop saw, however even a small saw with only an eight-inch blade will often be able to cut material up to 12 inches wide.

What is the max depth of cut with Mitre saw?

The maximum depth of cut at 90° is 65mm with a stock width of 305mm. The mitre range is 45° to 60°. At 45° bevel angle and at 45° mitre angle, the depth of cut is a useful 50mm with a stock width of 215mm.

How deep can a 12-inch miter saw cut?

Manufacturers also make 12-inch versions, which have a maximum cut of about 7 1/2 inches, wide enough for two-by-eights. This larger saw can cut a maximum thickness of 3 1/2 inches, enough to cut through four-by-fours.

How deep can 10 inch miter saw cut?

Saws start to differ when you look at their blade diameter—commonly 10 inches or 12 inches. The bigger the blade, the deeper and wider its maximum cut. Typically, a 10-inch miter saw will cut a 2 x 6 at 90 degrees and a 2 x 4 at 45 degrees; a 12-inch miter saw will cut a 2 x 8 at 90 degrees and a 2 x 6 at 45 degrees.

Can a miter saw cut a 6×6?

The geometry that makes it a wide, flat cutter works against it with a taller block. No saw could cut through a 4×4 at a 45-degree bevel angle, nor could any cross-cut a 6×6. The capacities in the specs (page 36) are based on the widest and thickest pieces that could be cut laying flat.

Can you cut a 4×4 with a 12-inch miter saw?

12-inch Miter Saw The two best miter saws to cuts a 4×4 post uses either a 12-inch or a 10-inch blade on a sliding miter saw. Both power saws have the cutting capacity to cut a 4×4 in one pass. A single pass is preferable to maintain the straight lines and integrity of the cut.

Can you put a 10-inch blade on a 12-inch miter saw?

You can put your 10-inch blades on your 12-inch saw (assuming the arbor holes are the same size), but you cannot put 12-inch blades on a 10-inch saw. The 12-inch saw gives you greater versatility – with the larger blade, it’s the hefty workhorse, and with the smaller blade, it’s a master of precision.

Can you use a miter saw on the ground?

We don’t recommend using a miter saw on the ground. It’s a trip hazard and can lead to a back injury from handling a heavy saw (often 50lbs+) and lumber. Most manufacturers recommend bolting down a miter saw before use, which is difficult to do on the floor but can be achieved on a workbench.

Can a 7 1 4 miter saw cut a 4×4?

Like any saw with a 7 1/4” blade, no. Not in one cut. But it’s not intended for large materials like that. If I needed to make cuts on 4X lumber I’ll get a 10” or 12” miter saw out and run a cord.

What is the difference between a compound miter saw and a miter saw?

A miter saw is a specialized tool that lets you make cuts at a variety of angles. The saw has a blade mounted on a swing arm that pivots left or right to produce angled cuts. Compound miter saws feature blades that pivot left and right for angled cuts and tilt in a single direction for beveled cuts.

Can you set depth on Mitre saw?

yes the do have depth stops but some a re better than others as they can have quite a bit of flex in them.

Can you set the depth of cut on a miter saw?

How it works. If your miter saw has a flip down stop, you can use it to limit how far the blade will penetrate into your material. The combination of the flip stop and, on most saws, a bolt, lets you dial in depth of cut pretty accurately. Of course when the flip stop is out of the way, you can cut full depth.

What is trenching on a Mitre saw?

Mitre saws are now appearing with a trenching facility which is basically an adjustable depth stop.