Resetting the SRS Light To do this, turn the key in the ignition, but do not start the car. Just turn it far enough to turn on the electrical. As soon as the SRS indicator light turns off, then turn the key to the off position and then turn it on again. Repeat this procedure about 5-7 times.
Contents
- 1 How do I reset my SRS?
- 2 What causes an SRS light to come on?
- 3 Will disconnecting battery reset SRS light?
- 4 How do you reset the airbag light on a Toyota Tundra?
- 5 How much does it cost to reset the airbag light?
- 6 Where is the SRS fuse?
- 7 How do you reset the airbag light on a 2007 Toyota Corolla?
- 8 Can you drive with the SRS light on?
- 9 What is the SRS code?
- 10 Why is my airbag light coming on and off?
- 11 Is it legal to reset airbag module?
- 12 Where is the airbag module located?
- 13 What happens if you disconnect airbag sensor?
How do I reset my SRS?
Reset Your SRS Light
- There is a yellow plug under the dash plugged into the fuse panel.
- Turn the ignition key to the “ON” (II) position.
- When the SRS light comes back on plug the jumper wire back in within 4 seconds the light will blink twice and go out.
- Unplug the jumper and turn the ignition key off.
What causes an SRS light to come on?
If the SRS light stays on or starts flashing on and off, you may have a problem with the airbags themselves, a loose wire, a faulty seat belt buckle, or a problem with the Engine Control Unit (ECU) that is causing the airbag warning light to stay on.
Will disconnecting battery reset SRS light?
Often, all it takes to get rid of that pesky warning light is to reset your airbag sensor. Remove the terminal clamp and leave it disconnected for 5-10 seconds to allow the airbag sensor to reset. Then reconnect the battery terminal and turn the vehicle on. With a bit of luck, the light will stay off.
How do you reset the airbag light on a Toyota Tundra?
To reset the toyota tundra airbag light, put the key in the ignition and put it in the on position without starting the engine. Wait for 5 minutes and replace the ecu fuse.
How much does it cost to reset the airbag light?
Number 1 — Reset Airbag Light You’ll need to hire a professional to come in and examine the airbags before you continue to drive the car. This process can take several hours of time and usually costs a few hundred dollars, although depending upon the type of car it may be up to about $600.
Where is the SRS fuse?
Where is the fuse for SRS light? The fuse block is on the driver’s side of the engine compartment. Pull out the SRS fuse. In most models, this is fuse #40, located in the lower right corner of the fuse block.
How do you reset the airbag light on a 2007 Toyota Corolla?
Unbend a paperclip and jump the two electrical terminals by touching one end of the paperclip to one terminal on the connector and the other end of the paperclip to the other end of the terminal. This will jump the two terminals, and cause the SRS light on your dash to stay lit for 10 seconds.
Can you drive with the SRS light on?
While you can certainly drive while your SRS light is on, it isn’t safe. You should get your vehicle to a service center as soon as possible so that a technician can inspect your SRS computer.
What is the SRS code?
The SRS warning light refers to the Supplemental Restraint System (SRS) and is most commonly known as the airbag system light. This is a computer controlled system designed to deploy one or more driver, passenger, and side airbags.
Why is my airbag light coming on and off?
When the airbag light turns on, this means that the airbag system is not properly functioning. If your vehicle—and airbag system—is working properly, the light should remain off. Or, in some vehicles, it may turn on for a few seconds along with all other displays and then immediately dim out. This is normal.
Is it legal to reset airbag module?
You certainly can remove the SRS airbag module from your vehicle and reset the unit to factory settings; you need to have the right tools and follow the steps correctly to succeed in resetting it properly. To begin the process, you need to remove the SRS airbag module from your vehicle.
Where is the airbag module located?
In most cars it is under the center console that is between the two front seats, or center of the dash on the floor. In most GM cars it is under the driver or passenger seat. Disconnect the positive battery cable and wait 3 min. You are now safe to unplug the airbag control module harness wiring plugs.
What happens if you disconnect airbag sensor?
What happens if you unplug airbag module? Disconnecting the airbag unit from the harness without unplugging the battery may trigger the airbags to deploy or may cause damage to the computer system. After disconnecting the positive battery cable, you should wait three minutes before removing the computer module.
